Log in
Search
Latest topics
» Testers Sprite engine swapby Greenman38633 Today at 9:32 pm
» Elfin 0.5cc (Arnie Hende replica)
by dan vincent Today at 9:18 pm
» Introducing our Cox .049 TD Engines
by layback209 Today at 9:10 pm
» Anderson Baby Spitfire - looking for the aft tank and gasket
by Boats13 Today at 8:18 pm
» Fuel residue stain clening help
by akjgardner Today at 7:53 pm
» my attempt at making an exhaust throttle for Cox .049
by roddie Today at 7:00 pm
» Another of C.T. engines cleaned ---- Cox Tee Dee .09 --- Just today (3/26/2024) more Cox parts
by sosam117 Today at 5:55 pm
» Cox powered boat litle shrimp hidroplane
by davidll1984 Today at 2:52 pm
» Introducing the new - "QZ" RR-1
by roddie Today at 1:08 pm
» STUKA bomb dimentions needed
by latole Today at 9:36 am
» Indexing COX cylinders
by davidll1984 Today at 7:56 am
» 1/2a Skyray plans?
by 944_Jim Yesterday at 10:14 pm
Dale Kirn rough drawing of Tee Dee info
Page 1 of 1
Dale Kirn rough drawing of Tee Dee info
In my photo gallery FAIF2D on this site there is a very bad scan of a series of sketches on one sheet that I got from Dale at his house back in the late 70's early 80's. Some of the info is the dimensions off the original drawings and some are of speed secrets. I hope that when you get the file open it will be readable. The sketches were made on the back of my briefcase while balancing it on my leg and is old and faded but most of the information can been read.
Last edited by faif2d on Sat Dec 06, 2014 10:17 pm; edited 1 time in total (Reason for editing : site where the photo is.)
faif2d- Bronze Member
- Posts : 30
Join date : 2014-09-08
Location : texas
Re: Dale Kirn rough drawing of Tee Dee info
John ,Can I get a link // Thanks Eric
getback- Top Poster
-
Posts : 10028
Join date : 2013-01-18
Age : 66
Location : julian , NC
dckrsn- Diamond Member
- Posts : 2750
Join date : 2010-10-21
Age : 71
Location : Long Island, New York
Re: Dale Kirn rough drawing of Tee Dee info
It is a PDF so if you get the native file you can get it onto a page and blow it up so it is readable. If you blow up the page here to 200% the page becomes readable. The head mod is to make a low compression make almost as much power as a high compression one. It works I did this to a bunch that I got from him for 25 cents each. He got them from the ready to smash returns that could not be started. I also got a bunch of the black 5-3 props that the 3 came off of the mold and could not be sold. I got something like 100 of those at 25 cents each. I still have a few props left but the glow heads are all gone. He showed me a Spook kit and said that the big Otto kit was almost a direct copy. I knew where there was one in Fort Worth so purchased it and sent it to him as thanks for all the goodies.
faif2d- Bronze Member
- Posts : 30
Join date : 2014-09-08
Location : texas
Similar topics
» Dale Kirn has passed on
» Dale Kirn's 290 Special
» Santana plans by Dale Kirn now available
» Tapered piston?
» "Torquette" 1/2A Biplane by Dale Kirn...September, 1966 Flying Models
» Dale Kirn's 290 Special
» Santana plans by Dale Kirn now available
» Tapered piston?
» "Torquette" 1/2A Biplane by Dale Kirn...September, 1966 Flying Models
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum