Log in
Search
Latest topics
» audio-tach anyone?by balogh Today at 7:04 am
» Prop Rod - resto to a runner
by getback Today at 6:19 am
» WenMac 049 - Glow Plug & Head Gasket replacements?
by Ken Cook Yesterday at 7:50 pm
» 12 string guitar suggestions
by akjgardner Yesterday at 7:08 pm
» A choke-tube with velocity-stack configured Bee
by roddie Yesterday at 2:54 pm
» Jim Walkers FireBee - This is going to be fun
by rsv1cox Yesterday at 2:43 pm
» Nostalgia alert, my 1959 Corvette revisited
by Admin Yesterday at 1:11 pm
» Hawk had breakfast and then took a bath
by rsv1cox Yesterday at 10:26 am
» Jim Walker Firebaby
by rdw777 Sat May 18, 2024 4:58 pm
» Prayers for my Wife Please
by akjgardner Sat May 18, 2024 10:28 am
» Cox prop rod
by Wiggy Fri May 17, 2024 4:30 pm
» "Red Neck" .049 elec. starter
by getback Fri May 17, 2024 7:19 am
Another Cox Mercedes with a broken needle tip
Page 1 of 1
Another Cox Mercedes with a broken needle tip
This is getting to be a trend. Second time in eight Mercedes engines. Only times I have ever seen it. But, others here have experienced it also. Thankfully this broken needle was standard size, not the long handle needle most found on these.
I know these engines in such a confined space get hot despite the cooling fan doing it's best. But two out of eight. It may be partly because the hood on these cars interferes with the needle and PO's screw them down tight to reduce the height of the needle above the hood and consequently the interference. And/or they may be castor locked. But this one was loose.
After seeing this before, the cure was simple. I just inserted the broken needle in the insert, heated and pulled. Came right out. But this insert was level with the surface of the back plate not elevated like all others.
The orifice in the insert for some reason is smaller than the previous one, it took a pin to remove it as the wire I used to remove the other stuck needle tip would not go through this one.
I know these engines in such a confined space get hot despite the cooling fan doing it's best. But two out of eight. It may be partly because the hood on these cars interferes with the needle and PO's screw them down tight to reduce the height of the needle above the hood and consequently the interference. And/or they may be castor locked. But this one was loose.
After seeing this before, the cure was simple. I just inserted the broken needle in the insert, heated and pulled. Came right out. But this insert was level with the surface of the back plate not elevated like all others.
The orifice in the insert for some reason is smaller than the previous one, it took a pin to remove it as the wire I used to remove the other stuck needle tip would not go through this one.
rsv1cox- Top Poster
-
Posts : 10660
Join date : 2014-08-18
Location : West Virginia
Re: Another Cox Mercedes with a broken needle tip
Just another day of Cox rescue for one of our own. Seems to be a regular occurance. Good job on another fine save. Thanks for sharing.
NEW222- Top Poster
- Posts : 3892
Join date : 2011-08-13
Age : 45
Location : oakbank, mb
Re: Another Cox Mercedes with a broken needle tip
NEW222 wrote:Just another day of Cox rescue for one of our own. Seems to be a regular occurance. Good job on another fine save. Thanks for sharing.
+1
SteveM- Bronze Member
- Posts : 48
Join date : 2018-11-27
Age : 59
Location : Palatine, Illinois
Similar topics
» P-40 broken elevator; how I fix it
» broken again!!!
» ebay Cox Mercedes, rough.....but check out that glow head.
» Cox Mercedes W-196 - New on me
» Automobiles you don't see everyday...
» broken again!!!
» ebay Cox Mercedes, rough.....but check out that glow head.
» Cox Mercedes W-196 - New on me
» Automobiles you don't see everyday...
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum