Log in
Search
Latest topics
» audio-tach anyone?by roddie Today at 12:14 pm
» Jim Walkers FireBee - This is going to be fun
by rdw777 Today at 11:22 am
» Prayers for my Wife Please
by fit90 Today at 8:34 am
» Prop Rod - resto to a runner
by getback Today at 7:19 am
» WenMac 049 - Glow Plug & Head Gasket replacements?
by Ken Cook Yesterday at 8:50 pm
» 12 string guitar suggestions
by akjgardner Yesterday at 8:08 pm
» A choke-tube with velocity-stack configured Bee
by roddie Yesterday at 3:54 pm
» Nostalgia alert, my 1959 Corvette revisited
by Admin Yesterday at 2:11 pm
» Hawk had breakfast and then took a bath
by rsv1cox Yesterday at 11:26 am
» Jim Walker Firebaby
by rdw777 Sat May 18, 2024 5:58 pm
» Cox prop rod
by Wiggy Fri May 17, 2024 5:30 pm
» "Red Neck" .049 elec. starter
by getback Fri May 17, 2024 8:19 am
Tower Hobbies Power Panel
Page 1 of 1
Tower Hobbies Power Panel
https://www.towerhobbies.com/cgi-bin/wti0001p?&I=LXACW8&P=ML I have one of these and recently it atarted putting out 12V from the glow plug outlet , i have not taken it apart yet but was wondering if anyone has had this problem and been able to fix it ? Thanks in advance
getback- Top Poster
-
Posts : 10170
Join date : 2013-01-18
Age : 66
Location : julian , NC
Re: Tower Hobbies Power Panel
Probably the MOSFET that drives the glow driver circuit shorted out. Can test with an ohm meter across drain and source. If you measure close to 0 ohms with the power removed that’s your problem.
Take a pic of the back of it.
Take a pic of the back of it.
Jason_WI- Top Poster
-
Posts : 3123
Join date : 2011-10-09
Age : 48
Location : Neenah, WI
Re: Tower Hobbies Power Panel
mine did this
I am a HAM...means.... I am dangerous with a multi-meter
Too many el cheapo surface mount components
VDC output should be 1.2...measured as 11.7 (Batt Voltage....) some component was shorted ..no clue what one
I just replaced it with the slightly more expensive Hobbico version...they are the exact same part so 3 bucks more no diff on warranty....
I am a HAM...means.... I am dangerous with a multi-meter
Too many el cheapo surface mount components
VDC output should be 1.2...measured as 11.7 (Batt Voltage....) some component was shorted ..no clue what one
I just replaced it with the slightly more expensive Hobbico version...they are the exact same part so 3 bucks more no diff on warranty....
fredvon4- Top Poster
-
Posts : 4002
Join date : 2011-08-26
Age : 68
Location : Lampasas Texas
getback- Top Poster
-
Posts : 10170
Join date : 2013-01-18
Age : 66
Location : julian , NC
Similar topics
» Tower Hobbies RC 049?
» Tower Hobbies Sweepstakes
» "Red Neck" .049 elec. starter
» Free shipping from tower Hobbies thru October 31st
» Power Panel
» Tower Hobbies Sweepstakes
» "Red Neck" .049 elec. starter
» Free shipping from tower Hobbies thru October 31st
» Power Panel
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum