Log in
Search
Latest topics
» WenMac 049 - Glow Plug & Head Gasket replacements?by Ken Cook Today at 3:17 pm
» audio-tach anyone?
by roddie Today at 2:58 pm
» A choke-tube with velocity-stack configured Bee
by roddie Today at 2:54 pm
» Jim Walkers FireBee - This is going to be fun
by rsv1cox Today at 2:43 pm
» 12 string guitar suggestions
by 1/2A Nut Today at 1:58 pm
» Nostalgia alert, my 1959 Corvette revisited
by Admin Today at 1:11 pm
» Hawk had breakfast and then took a bath
by rsv1cox Today at 10:26 am
» Prop Rod - resto to a runner
by rsv1cox Today at 7:32 am
» Jim Walker Firebaby
by rdw777 Yesterday at 4:58 pm
» Prayers for my Wife Please
by akjgardner Yesterday at 10:28 am
» Cox prop rod
by Wiggy Fri May 17, 2024 4:30 pm
» "Red Neck" .049 elec. starter
by getback Fri May 17, 2024 7:19 am
old but interesting Cox fuel oil debate
Page 1 of 1
old but interesting Cox fuel oil debate
I got the link from
http://controlline.org.uk/phpBB2/viewtopic.php?t=15513&highlight=
https://www.rcgroups.com/forums/showthread.php?1325147-Cox-oil-testing-findings
Bernie has a few very interesting posts page 3 or 4
http://controlline.org.uk/phpBB2/viewtopic.php?t=15513&highlight=
https://www.rcgroups.com/forums/showthread.php?1325147-Cox-oil-testing-findings
Bernie has a few very interesting posts page 3 or 4
fredvon4- Top Poster
-
Posts : 4002
Join date : 2011-08-26
Age : 68
Location : Lampasas Texas
Re: old but interesting Cox fuel oil debate
Thanks Fred, very interesting read indeed...especially where Bernie chimed in and commented about the Estes and pre-Estes tolerances of the COX cylinder/piston combo.
@ Bernie, if you read this, I am wondering if finally you have managed to find a manufacturer for the 049 TD cylinder/piston sets with the pre-Estes OEM tolerances? I understand the TD cylinder/piston combos you sell are still the modifications of the double-slit exhaust Surestart cylinders?
The posts about the castor and synt oil experiments on COX engines is also very interesting. Even though the blackened piston top in a COX engine may suggest to some that the engine is misused at high temperature, in fact I always thought the high temperature of the piston top is the key to forming the protective varnish in the ball-joint cup.
My oldest TD051 with the black piston top had its balljoint set only once in its near 300 (!) hours of dependable run it performed in my RC Toucans.
@ Bernie, if you read this, I am wondering if finally you have managed to find a manufacturer for the 049 TD cylinder/piston sets with the pre-Estes OEM tolerances? I understand the TD cylinder/piston combos you sell are still the modifications of the double-slit exhaust Surestart cylinders?
The posts about the castor and synt oil experiments on COX engines is also very interesting. Even though the blackened piston top in a COX engine may suggest to some that the engine is misused at high temperature, in fact I always thought the high temperature of the piston top is the key to forming the protective varnish in the ball-joint cup.
My oldest TD051 with the black piston top had its balljoint set only once in its near 300 (!) hours of dependable run it performed in my RC Toucans.
balogh- Top Poster
-
Posts : 4755
Join date : 2011-11-06
Age : 65
Location : Budapest Hungary
Re: old but interesting Cox fuel oil debate
I have severely abused TeeDee 049/051 on nose of combat planes with up to 50% Nitro and almost always oil with more castor than synth ...later on Ken Cooks writings I shifted to more synt ratio and less total oil %....down to 20~22%....over RPM breakage were always crank pin or shaft....neve poked a rod through piston top....never bent a rod......I don't think I have ever owned a cox 6x3 prop.....
most interesting screw up....launched at something way over 20K rpm and motor quit in three laps.....get plane...motor and piston ok...no cylinder or head to be found....finger tight I guess.....
I strongly disagree with OP that resetting is not needed and the slop is not a problem.....he seems to believe (despite his blown pistons) that rod end gap and hammering in use is not the cause for the wear....funny considering his pedigree.....I used wrong fuel oil mix in one of the outboard engines he is engineer on Low end Force 15 HP (generic Mercruiser) and shattered a piston way out on the lake.....grrrrrrr
most interesting screw up....launched at something way over 20K rpm and motor quit in three laps.....get plane...motor and piston ok...no cylinder or head to be found....finger tight I guess.....
I strongly disagree with OP that resetting is not needed and the slop is not a problem.....he seems to believe (despite his blown pistons) that rod end gap and hammering in use is not the cause for the wear....funny considering his pedigree.....I used wrong fuel oil mix in one of the outboard engines he is engineer on Low end Force 15 HP (generic Mercruiser) and shattered a piston way out on the lake.....grrrrrrr
fredvon4- Top Poster
-
Posts : 4002
Join date : 2011-08-26
Age : 68
Location : Lampasas Texas
Re: old but interesting Cox fuel oil debate
Haha Fred I also lost one fingertight cylinder and head mid-air years ago..
balogh- Top Poster
-
Posts : 4755
Join date : 2011-11-06
Age : 65
Location : Budapest Hungary
Similar topics
» Fuel line that stays on a td fuel niibble
» The engine comment debate!
» Interesting
» Diesel Fuel being sold by EX Model Engines --- Whatis the % of the fuel mix?
» glow fuel Experiment with water contaminated nitro fuel
» The engine comment debate!
» Interesting
» Diesel Fuel being sold by EX Model Engines --- Whatis the % of the fuel mix?
» glow fuel Experiment with water contaminated nitro fuel
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum