Log in
Search
Latest topics
» Jim Walker Firebaby by rdw777 Today at 5:36 pm
» Norvel Needle Needed
by Greenman38633 Today at 5:36 pm
» World's largest weathervane
by Cox International Today at 3:38 pm
» My Cox .049 Marine inboard engine
by 1/2A Nut Today at 2:42 pm
» A prototype Cox Reed-valve marine engine
by F4D Phantom II Today at 2:22 pm
» Help Pee Wee tank cap .020
by rdw777 Today at 1:30 pm
» **VOTE-ON-THE-NEXT-COX-ENGINE-OF-THE-MONTH** (May 2024)
by GallopingGhostler Today at 11:34 am
» Here we go again... another Lawn-Boy
by rdw777 Today at 9:17 am
» Revivng Some Childhood Classics
by getback Today at 8:21 am
» Roddie-Rigger.. a 2005 original design
by getback Today at 6:31 am
» Jim Walkers FireBee - This is going to be fun
by rsv1cox Yesterday at 7:29 am
» Post your Older books
by rsv1cox Mon May 06, 2024 7:51 pm
Cox Engine of The Month
Queen Bee motor mount?
Page 1 of 1
Queen Bee motor mount?
Any recommendations for a QB motor mount? Hayes used to list one just for it, but NLA.
I was thinking of either hogging out their long mount for an .049 or using the long .09 mount (which would be a bit sloppy: screws close to edge). Just wondering if anyone had experience (good or bad) with either...
I was thinking of either hogging out their long mount for an .049 or using the long .09 mount (which would be a bit sloppy: screws close to edge). Just wondering if anyone had experience (good or bad) with either...
ahrma_581- Gold Member
- Posts : 290
Join date : 2012-03-21
Location : Sonoran desert
Re: Queen Bee motor mount?
Hey, looky what I found.
Hope this helps.
Bob
Bottom of the list.
http://www.sigmfg.com/cgi-bin/dpsmart.exe/IndexText/FHAY001.html?E+Sig
Hope this helps.
Bob
Bottom of the list.
http://www.sigmfg.com/cgi-bin/dpsmart.exe/IndexText/FHAY001.html?E+Sig
dckrsn- Diamond Member
- Posts : 2750
Join date : 2010-10-21
Age : 71
Location : Long Island, New York
Re: Queen Bee motor mount?
Muchos Gracias!! (Cinco de Mayo an' all)
I had been to this page http://sigmfg.com/cgi-bin/dpsmart.exe/MainMenuFV5.html?E+Sig and it cuts off at 'HAY021'. The 'Next Results Screen' button (which is only visible when you scroll to the bottom) pulls up HAY022 and HAY023 (which is the QB mount).
I had been to this page http://sigmfg.com/cgi-bin/dpsmart.exe/MainMenuFV5.html?E+Sig and it cuts off at 'HAY021'. The 'Next Results Screen' button (which is only visible when you scroll to the bottom) pulls up HAY022 and HAY023 (which is the QB mount).
ahrma_581- Gold Member
- Posts : 290
Join date : 2012-03-21
Location : Sonoran desert
Similar topics
» NIP Cox .09 motor mount
» Scans of my Lil Wizard rubber band engine mount
» Postage stamp backplate mount?
» What do I have?
» Brushless motor mounted to 3D mount looking like a Golden Bee
» Scans of my Lil Wizard rubber band engine mount
» Postage stamp backplate mount?
» What do I have?
» Brushless motor mounted to 3D mount looking like a Golden Bee
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum