Log in
Search
Latest topics
» 12 string guitar suggestions by akjgardner Today at 11:36 am
» A choke-tube with velocity-stack configured Bee
by roddie Today at 10:48 am
» Hawk had breakfast and then took a bath
by rsv1cox Today at 10:26 am
» Jim Walkers FireBee - This is going to be fun
by getback Today at 9:55 am
» WenMac 049 - Glow Plug & Head Gasket replacements?
by Ken Cook Today at 8:06 am
» Prop Rod - resto to a runner
by rsv1cox Today at 7:32 am
» Jim Walker Firebaby
by rdw777 Yesterday at 4:58 pm
» Nostalgia alert, my 1959 Corvette revisited
by rsv1cox Yesterday at 2:25 pm
» Prayers for my Wife Please
by akjgardner Yesterday at 10:28 am
» Cox prop rod
by Wiggy Fri May 17, 2024 4:30 pm
» "Red Neck" .049 elec. starter
by getback Fri May 17, 2024 7:19 am
» Cox prop rod
by Wiggy Fri May 17, 2024 5:35 am
aluminum fuel tubing ??
Page 1 of 1
aluminum fuel tubing ??
just was at the want to be my hobby store HL that is , any way I seen and experienced it green corrosion on copper tubing .. saw that they had aluminum tubing, can you not use aluminum tubing ?? through the rubber stoppers is it the bending ? never tried to that I can't remember.
getback- Top Poster
-
Posts : 10168
Join date : 2013-01-18
Age : 66
Location : julian , NC
Re: aluminum fuel tubing ??
Aluminum is very soft. It will need a supporting tool to put it through the stopper is correct. Music wire and a wheel collar might be all you need to push it through. I am not sure if there are any other problems with it due to softness and tube length, but suspect there might be.
The aluminum interacts better than brass with the fuel. The green goo will still form, as that is mostly partially solidified castor oil and other contaminants.
Phil
The aluminum interacts better than brass with the fuel. The green goo will still form, as that is mostly partially solidified castor oil and other contaminants.
Phil
pkrankow- Top Poster
- Posts : 3025
Join date : 2012-10-02
Location : Ohio
getback- Top Poster
-
Posts : 10168
Join date : 2013-01-18
Age : 66
Location : julian , NC
Re: aluminum fuel tubing ??
FYI:
The chief advantage of aluminum fuel tubing it that it may be easily bent and shaped using a tubing bending tool. The trick is to shape the tubing in proggresive steps rather than all at once.
I have such a tool for shaping automotive hydraulic brake lines. With care it works well on aluminum fuel tubing too.
SD
The chief advantage of aluminum fuel tubing it that it may be easily bent and shaped using a tubing bending tool. The trick is to shape the tubing in proggresive steps rather than all at once.
I have such a tool for shaping automotive hydraulic brake lines. With care it works well on aluminum fuel tubing too.
SD
SuperDave- Rest In Peace
- Posts : 3552
Join date : 2011-08-13
Location : Washington (state)
Re: aluminum fuel tubing ??
I have a set of coil springs that fit over tubing to prevent distortion, Hobby Lobby the craft store sells a set, as do many other stores.
I also have a couple pieces of wire cable I can put inside certain sizes of tubing for the same purpose, but my choices are limited with the cable. The pieces are "scrap" cutoffs from various sources.
The better benders I have used have "tall" sides that contain the tube exactly so the tubing will remain more or less round instead of flattening.
Phil
I also have a couple pieces of wire cable I can put inside certain sizes of tubing for the same purpose, but my choices are limited with the cable. The pieces are "scrap" cutoffs from various sources.
The better benders I have used have "tall" sides that contain the tube exactly so the tubing will remain more or less round instead of flattening.
Phil
pkrankow- Top Poster
- Posts : 3025
Join date : 2012-10-02
Location : Ohio
Bending tube
The coil spring around the tube works best but an old plumber's trick is to fill the tube with sand before bending or wrap solder around the tube!
RK Flyer
RK Flyer
RK Flyer- Gold Member
- Posts : 274
Join date : 2013-07-16
Location : Somerset, Kentucky
Re: aluminum fuel tubing ??
_________________
Don't Panic!
...and never Ever think about how good you are at something...
while you're doing it!
My Hot Rock & Blues Playlist
...and never Ever think about how good you are at something...
while you're doing it!
My Hot Rock & Blues Playlist
RknRusty- Rest In Peace
- Posts : 10869
Join date : 2011-08-10
Age : 68
Location : South Carolina, USA
Re: aluminum fuel tubing ??
Rusty,
Thanks for the link, I've been looking for one of those.
Jim
Thanks for the link, I've been looking for one of those.
Jim
JPvelo- Diamond Member
- Posts : 1972
Join date : 2011-12-02
Age : 56
Location : Colorado
Re: aluminum fuel tubing ??
I do have the spring tube benders dift. sizes found them upstairs in the hobby room that's full of stuff . But I do like that bender rusty Eric
getback- Top Poster
-
Posts : 10168
Join date : 2013-01-18
Age : 66
Location : julian , NC
Similar topics
» fuel tubing size
» Cox baby Bee internal fuel tubing
» Cox Engine Fuel Tubing Elbow Fitting?
» Aluminum td 010 020 fuel tank and collars
» Nylon tubing
» Cox baby Bee internal fuel tubing
» Cox Engine Fuel Tubing Elbow Fitting?
» Aluminum td 010 020 fuel tank and collars
» Nylon tubing
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum