Log in
Search
Latest topics
» Nostalgia alert, my 1959 Corvette revisitedby rsv1cox Today at 12:18 pm
» audio-tach anyone?
by roddie Today at 11:14 am
» Jim Walkers FireBee - This is going to be fun
by rdw777 Today at 10:22 am
» Prayers for my Wife Please
by fit90 Today at 7:34 am
» Prop Rod - resto to a runner
by getback Today at 6:19 am
» WenMac 049 - Glow Plug & Head Gasket replacements?
by Ken Cook Yesterday at 7:50 pm
» 12 string guitar suggestions
by akjgardner Yesterday at 7:08 pm
» A choke-tube with velocity-stack configured Bee
by roddie Yesterday at 2:54 pm
» Hawk had breakfast and then took a bath
by rsv1cox Yesterday at 10:26 am
» Jim Walker Firebaby
by rdw777 Sat May 18, 2024 4:58 pm
» Cox prop rod
by Wiggy Fri May 17, 2024 4:30 pm
» "Red Neck" .049 elec. starter
by getback Fri May 17, 2024 7:19 am
Looking for plan's for the "Lil Wizard"
Page 3 of 3
Page 3 of 3 • 1, 2, 3
Re: Looking for plan's for the "Lil Wizard"
So the fuse is 1/4' wing is 1/8" the stab and elevator ? the doublers for the fuse 1/8" also ? Give or take a mm , my wood is in inches Eric
getback- Top Poster
-
Posts : 10170
Join date : 2013-01-18
Age : 66
Location : julian , NC
Re: Looking for plan's for the "Lil Wizard"
There are different generations of this plane. My plane has 1/16 plywood doublers. Another picture shows 1/8 balsa doublers.
In both cases sand the fairing on the edges before gluing. It cannot be done effectively after gluing.
Phil
In both cases sand the fairing on the edges before gluing. It cannot be done effectively after gluing.
Phil
pkrankow- Top Poster
- Posts : 3025
Join date : 2012-10-02
Location : Ohio
Re: Looking for plan's for the "Lil Wizard"
So could I use 3mm ply?
cox24711- Platinum Member
- Posts : 722
Join date : 2014-01-18
Age : 21
Location : Noosa Queensland Australia
Re: Looking for plan's for the "Lil Wizard"
3mm light ply, probably.cox24711 wrote:So could I use 3mm ply?
2mm would be reasonable I think, 1.5mm might be better. Those sizes bracket 1/16 it would appear.
Phil
pkrankow- Top Poster
- Posts : 3025
Join date : 2012-10-02
Location : Ohio
Re: Looking for plan's for the "Lil Wizard"
Thanks for the Info Phil I will note that , I was wondering if it was ply or balsa , I have both but more balsa than the 1/16 ply. Now to get it scaled right . getback
getback- Top Poster
-
Posts : 10170
Join date : 2013-01-18
Age : 66
Location : julian , NC
Page 3 of 3 • 1, 2, 3
Similar topics
» WIZARD - a "Wonderful Wizard"
» Cox Powered Tether Pole Hovercraft - Plans Now In Building Plans
» CG on a L'il Wizard
» Bad Weekend For A Wizard.....
» *Cox Engine of The Month* Submit your pictures! -August 2016-
» Cox Powered Tether Pole Hovercraft - Plans Now In Building Plans
» CG on a L'il Wizard
» Bad Weekend For A Wizard.....
» *Cox Engine of The Month* Submit your pictures! -August 2016-
Page 3 of 3
Permissions in this forum:
You cannot reply to topics in this forum