Log in
Search
Latest topics
» A choke-tube with velocity-stack configured Beeby MauricioB Today at 12:37 am
» Jim Walkers FireBee - This is going to be fun
by cstatman Yesterday at 6:58 pm
» Prop Rod - resto to a runner
by cstatman Yesterday at 6:56 pm
» Hawk had breakfast and then took a bath
by rdw777 Yesterday at 5:38 pm
» Jim Walker Firebaby
by rdw777 Yesterday at 4:58 pm
» WenMac 049 - Glow Plug & Head Gasket replacements?
by rdw777 Yesterday at 4:32 pm
» Nostalgia alert, my 1959 Corvette revisited
by rsv1cox Yesterday at 2:25 pm
» Prayers for my Wife Please
by akjgardner Yesterday at 10:28 am
» Cox prop rod
by Wiggy Fri May 17, 2024 4:30 pm
» "Red Neck" .049 elec. starter
by getback Fri May 17, 2024 7:19 am
» Cox prop rod
by Wiggy Fri May 17, 2024 5:35 am
» Looking For Comet Tri-Pacer
by latole Fri May 17, 2024 3:45 am
Iron on covering
Page 1 of 1
Iron on covering
back in the 70's I usedtae paint Balsarite on open framework before applyin' iron on covering. Do ye think Doping framework prior tae iron on is ae good idea?
Scotland421- Silver Member
- Posts : 82
Join date : 2021-03-07
Re: Iron on covering
This is my two cents. I detest Balsarite and never found it to work as intended. I found that trying to thin it was quite difficult even though they didn't recommend doing so. In addition, it would cause wrinkles in the covering when in the direct sun. I found it to add a noticeable amount of weight when I used it on a entire full fuse model.
To my knowledge it's still made. They offered two versions, a fabric application and a iron on version. One was merely thicker than the other. When I used it on certain iron on films, I found it to make a mess especially at the seams where it would creep out. Sig offers Stix-It and I've found the solvents in that material too aggressive which causes certain coverings to separate their color and bleed out making a real mess. I've also found the heat to prevent the covering from tacking immediately to the balsa and then it slides on top of it.
A good iron on covering such as Ultracote or REAL Monokote doesn't require any additional adhesives. The new Monokote is worthless crap. Throw it out and don't even try and use it. It's not the product that revolutionized the hobby that many have used for the past 40 years. As like many other Chinese products, it's a cheap copy and the end user suffers from the lack of quality.
Placing dope under it in my opinion is asking for a compatibility issue. I've seen this when we've had old silkspan models with the covering all torn. Strip the open bays and Monokote the entire wing. I've never found the covering to attach as well as it did when you had new bare balsa. A good covering job isn't going to release. It will also prevent oil soaking better than paint does provided it's done properly.
To my knowledge it's still made. They offered two versions, a fabric application and a iron on version. One was merely thicker than the other. When I used it on certain iron on films, I found it to make a mess especially at the seams where it would creep out. Sig offers Stix-It and I've found the solvents in that material too aggressive which causes certain coverings to separate their color and bleed out making a real mess. I've also found the heat to prevent the covering from tacking immediately to the balsa and then it slides on top of it.
A good iron on covering such as Ultracote or REAL Monokote doesn't require any additional adhesives. The new Monokote is worthless crap. Throw it out and don't even try and use it. It's not the product that revolutionized the hobby that many have used for the past 40 years. As like many other Chinese products, it's a cheap copy and the end user suffers from the lack of quality.
Placing dope under it in my opinion is asking for a compatibility issue. I've seen this when we've had old silkspan models with the covering all torn. Strip the open bays and Monokote the entire wing. I've never found the covering to attach as well as it did when you had new bare balsa. A good covering job isn't going to release. It will also prevent oil soaking better than paint does provided it's done properly.
Ken Cook- Top Poster
- Posts : 5487
Join date : 2012-03-27
Location : pennsylvania
Re: Iron on covering
Thank ye Ken, that was the insight I was lookin' fae.
Scotland421- Silver Member
- Posts : 82
Join date : 2021-03-07
T
Hi Scotland 421, you UK based or over the pond ?
Solar film still stock some stuff.
I got 2 bottles of balsalock from them earlier this year, for use with litespan...
I believe slec do a similar product to balsalock, as do some other firms...
Solar film still stock some stuff.
I got 2 bottles of balsalock from them earlier this year, for use with litespan...
I believe slec do a similar product to balsalock, as do some other firms...
Coxfledgling- Gold Member
- Posts : 375
Join date : 2021-01-10
Location : Near Caernarfon, Snowdonia, Wales, UK
Re: Iron on covering
Fresh balsa with no coating will work best. Dope will tend to bubble with heat. I do admit to painting the inside of floatplane fuselages with clear or colour dope to minimize water absorption after a dunking though.
706jim- Gold Member
- Posts : 461
Join date : 2013-11-29
Similar topics
» Foam wing iron on covering
» Soldering iron?
» Covering iron shortage? ----- substitute?
» any tricks on covering EPS foam with low-heat covering?
» I repaired my sealing iron today
» Soldering iron?
» Covering iron shortage? ----- substitute?
» any tricks on covering EPS foam with low-heat covering?
» I repaired my sealing iron today
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum