Log in
Search
Latest topics
» WenMac 049 - Glow Plug & Head Gasket replacements?by Ken Cook Today at 3:17 pm
» audio-tach anyone?
by roddie Today at 2:58 pm
» A choke-tube with velocity-stack configured Bee
by roddie Today at 2:54 pm
» Jim Walkers FireBee - This is going to be fun
by rsv1cox Today at 2:43 pm
» 12 string guitar suggestions
by 1/2A Nut Today at 1:58 pm
» Nostalgia alert, my 1959 Corvette revisited
by Admin Today at 1:11 pm
» Hawk had breakfast and then took a bath
by rsv1cox Today at 10:26 am
» Prop Rod - resto to a runner
by rsv1cox Today at 7:32 am
» Jim Walker Firebaby
by rdw777 Yesterday at 4:58 pm
» Prayers for my Wife Please
by akjgardner Yesterday at 10:28 am
» Cox prop rod
by Wiggy Fri May 17, 2024 4:30 pm
» "Red Neck" .049 elec. starter
by getback Fri May 17, 2024 7:19 am
Mesh screen .049 Cox engines
Page 1 of 1
Mesh screen .049 Cox engines
I have been looking for one of these. When our old friend redbaroness put one up BIN for $22 I jumped on it.
This one appears to be no prize, one NIB would be a prize. Looks like the mesh seam is situated at the front, not a good look and is frayed a bit. Get's here next week.........maybe. But...........how do you remove the cylinder? Top fin slots didn't arrive until the slit cylinders, then only later.
From Sitter/Dannels:
"Painful burns"..................Poor babies out there. I was lucky to escape with finger whacks and just a little loss of blood.
This one appears to be no prize, one NIB would be a prize. Looks like the mesh seam is situated at the front, not a good look and is frayed a bit. Get's here next week.........maybe. But...........how do you remove the cylinder? Top fin slots didn't arrive until the slit cylinders, then only later.
From Sitter/Dannels:
"Painful burns"..................Poor babies out there. I was lucky to escape with finger whacks and just a little loss of blood.
rsv1cox- Top Poster
-
Posts : 10660
Join date : 2014-08-18
Location : West Virginia
Re: Mesh screen .049 Cox engines
Last edited by Marleysky on Mon Nov 15, 2021 11:47 am; edited 1 time in total (Reason for editing : added picture)
Marleysky- Top Poster
-
Posts : 3618
Join date : 2014-09-28
Age : 71
Location : Grand Rapids, MI
Re: Mesh screen .049 Cox engines
Do what Marleysky says.
Heat the cylinder up and then I would use the glo plug wrench on the glo plug and see which comes loose?
If the glo head unscrews then remove it and then file flat spots on the cylinder to where the Cox wrench fit the cylinder.
They probably assembled the screen over the cylinder then screwed the glow head into the cylinder, then screwed the cylinder into the crankcase and tightened the entire assembly with the wrench on the glow plug.
Then it was your problem to get the cylinder off, because I think the glow plug will come loose first. (any bets?)
That is what I would do.
Heat the cylinder up and then I would use the glo plug wrench on the glo plug and see which comes loose?
If the glo head unscrews then remove it and then file flat spots on the cylinder to where the Cox wrench fit the cylinder.
They probably assembled the screen over the cylinder then screwed the glow head into the cylinder, then screwed the cylinder into the crankcase and tightened the entire assembly with the wrench on the glow plug.
Then it was your problem to get the cylinder off, because I think the glow plug will come loose first. (any bets?)
That is what I would do.
sosam117- Diamond Member
- Posts : 1293
Join date : 2016-03-23
Location : Suburb of Chicago, Illinois
Re: Mesh screen .049 Cox engines
Here's another recipe, Bob(like you need one).
1. Heat the glow head(to expand and tighten it to the cylinder)
2. Heat the crankcase(to expand the case threads)
3. Try the head wrench to loosen the cylinder.
4. If necessary, try the inverted canned air trick.
Chilling the cylinder tightens it to the head and shrinks
the cylinder in the case. Got to work quickly to beat the
heat migration between parts. If all fails, hit the cylinder/case
threads with some sort of penetrating oil while its hot, and try
again tomorrow. If the head comes lose, you're probably going
to have to try the leather strap, or your choice of cylinderectomy.
I envy you Bob. I've never faced this challenge.
Good luck,
Bob
1. Heat the glow head(to expand and tighten it to the cylinder)
2. Heat the crankcase(to expand the case threads)
3. Try the head wrench to loosen the cylinder.
4. If necessary, try the inverted canned air trick.
Chilling the cylinder tightens it to the head and shrinks
the cylinder in the case. Got to work quickly to beat the
heat migration between parts. If all fails, hit the cylinder/case
threads with some sort of penetrating oil while its hot, and try
again tomorrow. If the head comes lose, you're probably going
to have to try the leather strap, or your choice of cylinderectomy.
I envy you Bob. I've never faced this challenge.
Good luck,
Bob
dckrsn- Diamond Member
- Posts : 2750
Join date : 2010-10-21
Age : 71
Location : Long Island, New York
Re: Mesh screen .049 Cox engines
Cool you got one coming , i have i think two of them and have sold about the same till I realized I should keep some for ME ! lol Maybe you want have to take the cylinder off ?!
getback- Top Poster
-
Posts : 10168
Join date : 2013-01-18
Age : 66
Location : julian , NC
Re: Mesh screen .049 Cox engines
Thanks all..........tricks of the trade.
Maybe I won't have to take it off. Depends on how castor locked the crank shaft is. I'll probably just run it once then mount it on one of those plastic mineral stands.
Maybe I won't have to take it off. Depends on how castor locked the crank shaft is. I'll probably just run it once then mount it on one of those plastic mineral stands.
rsv1cox- Top Poster
-
Posts : 10660
Join date : 2014-08-18
Location : West Virginia
Similar topics
» Venturi without mesh screen (installation) --- Enya Rear Induction engines too!
» .020 Mesh screen cylinder
» Cylinder Mesh Screen Size
» how do i install a new blackplate screen?
» The mesh Babe Bee and a slightly bent prop
» .020 Mesh screen cylinder
» Cylinder Mesh Screen Size
» how do i install a new blackplate screen?
» The mesh Babe Bee and a slightly bent prop
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum