Log in
Search
Latest topics
» Blue backplate postage stamp engineby getback Today at 6:46 am
» Cox Ryan ST 2.0
by rsv1cox Today at 6:38 am
» COX Postage Stamp engine -Babe Bee & Horseshoe Backplate adapters
by GallopingGhostler Today at 6:33 am
» Jim Walkers FireBee - This is going to be fun
by rsv1cox Yesterday at 3:45 pm
» Hawk had breakfast and then took a bath
by GallopingGhostler Yesterday at 2:34 pm
» Prop Rod - resto to a runner
by rsv1cox Yesterday at 12:41 pm
» Jim Walker Firebaby
by rsv1cox Yesterday at 12:24 pm
» Internet buy
by Ken Cook Yesterday at 9:15 am
» Artwork for Otto Kuhni
by GallopingGhostler Yesterday at 8:26 am
» Sherline lathe wont run
by getback Yesterday at 7:15 am
» Roddie's water-cooling bottle for bench-running
by roddie Tue May 14, 2024 7:38 pm
» Feed Station Zebra.. Spring 2022
by roddie Tue May 14, 2024 5:59 pm
Help GTP air snorkel
Page 1 of 1
Help GTP air snorkel
Hi
I need a way to keep the foam on top of the air snorkel, with the use tends to be lowered to the engine air inlet and shuts off the engine.
Thanks
Alejo
I need a way to keep the foam on top of the air snorkel, with the use tends to be lowered to the engine air inlet and shuts off the engine.
Thanks
Alejo
garza2014- Bronze Member
- Posts : 54
Join date : 2013-08-22
Age : 42
Location : Medellin, Colombia
Re: Help GTP air snorkel
Stick a straight pin through it and you should be good to go.
706jim- Gold Member
- Posts : 461
Join date : 2013-11-29
Re: Help GTP air snorkel
garza2014 wrote:Hi
I need a way to keep the foam on top of the air snorkel, with the use tends to be lowered to the engine air inlet and shuts off the engine.
Thanks
Alejo
Alejo: Hey, you stole my idea for a RC car emoticon. Have you tried a TINY bit of rubber glue on the edges of the foam piece. Let it dry a few seconds, then push into the tube. Make sure that the tube is dry and clean of oil. Try it. It may work for a while, then it will be full of dirt and debris and need to be replaced with a clean piece.
happydad
happydad- Rest In Peace
- Posts : 1592
Join date : 2012-05-28
Age : 78
Location : Escondido, CA
Not work
happydad wrote:garza2014 wrote:Hi
I need a way to keep the foam on top of the air snorkel, with the use tends to be lowered to the engine air inlet and shuts off the engine.
Thanks
Alejo
Alejo: Hey, you stole my idea for a RC car emoticon. Have you tried a TINY bit of rubber glue on the edges of the foam piece. Let it dry a few seconds, then push into the tube. Make sure that the tube is dry and clean of oil. Try it. It may work for a while, then it will be full of dirt and debris and need to be replaced with a clean piece.
happydad
Hi happydad
Already try it, but does not work suction is very strong (killer bee backplate)
Very nice emoticon
Alejo
garza2014- Bronze Member
- Posts : 54
Join date : 2013-08-22
Age : 42
Location : Medellin, Colombia
Re: Help GTP air snorkel
706jim wrote:Stick a straight pin through it and you should be good to go.
Good idea but I don't want to damage air snorkel, you mean place pin on top? Or through the plastic?
Alejo
garza2014- Bronze Member
- Posts : 54
Join date : 2013-08-22
Age : 42
Location : Medellin, Colombia
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum