Log in
Search
Latest topics
» A choke-tube with velocity-stack configured Beeby roddie Today at 10:48 am
» Hawk had breakfast and then took a bath
by rsv1cox Today at 10:26 am
» Jim Walkers FireBee - This is going to be fun
by getback Today at 9:55 am
» WenMac 049 - Glow Plug & Head Gasket replacements?
by Ken Cook Today at 8:06 am
» Prop Rod - resto to a runner
by rsv1cox Today at 7:32 am
» Jim Walker Firebaby
by rdw777 Yesterday at 4:58 pm
» Nostalgia alert, my 1959 Corvette revisited
by rsv1cox Yesterday at 2:25 pm
» Prayers for my Wife Please
by akjgardner Yesterday at 10:28 am
» Cox prop rod
by Wiggy Fri May 17, 2024 4:30 pm
» "Red Neck" .049 elec. starter
by getback Fri May 17, 2024 7:19 am
» Cox prop rod
by Wiggy Fri May 17, 2024 5:35 am
» Looking For Comet Tri-Pacer
by latole Fri May 17, 2024 3:45 am
Pushrod for PT19
Page 1 of 1
Pushrod for PT19
Hi all, got a question, I removed the push rod out of my PT so a friend of mine could duplicate it for one that he had. Of course I got it back but that was over a year ago and now for the life of me can't remember where I put the dang thing. So I was wondering if anyone had spare or a pattern of one so I can make a replacement. I'm trying to get back together so I can pack it away since I'm going to be moving again soon to a better area any help will be appreciated. Thanks all (Bandit)
TDbandit- Platinum Member
- Posts : 897
Join date : 2014-12-01
Age : 52
Location : Riverdale Georgia
Push rod
Hi tdbandit, can't help with specifics but you have enough info in the fuz, hole size etc..
From memory the rod was thin solid wire.
Centralise the bell crank and stabiliser and measure. Piano wire is available of various sizes in the uk, and probably USA as well.
Could you help me out please by taking a side view picture of the fuz against a ruler, so I can better guestimates fuz Measurements so I can make a balsa fuz to make the 2 pt19 wings I have fly again please. That would be so helpful for me.
Thanks. Also an outline of the stabiliser would be good too.
Stay safe out there...
From memory the rod was thin solid wire.
Centralise the bell crank and stabiliser and measure. Piano wire is available of various sizes in the uk, and probably USA as well.
Could you help me out please by taking a side view picture of the fuz against a ruler, so I can better guestimates fuz Measurements so I can make a balsa fuz to make the 2 pt19 wings I have fly again please. That would be so helpful for me.
Thanks. Also an outline of the stabiliser would be good too.
Stay safe out there...
Coxfledgling- Gold Member
- Posts : 375
Join date : 2021-01-10
Location : Near Caernarfon, Snowdonia, Wales, UK
getback- Top Poster
-
Posts : 10168
Join date : 2013-01-18
Age : 66
Location : julian , NC
Pt19
Oh brill, thank you, will learn how to print the pictures off and then use the info...as said I have 2 wings and engines...
Coxfledgling- Gold Member
- Posts : 375
Join date : 2021-01-10
Location : Near Caernarfon, Snowdonia, Wales, UK
Re: Pushrod for PT19
Thanks for the info made up a new one sorry for the delay in replying been busy. I never had to make a new one so never though to measure it before. Thanks guys (Bandit)
TDbandit- Platinum Member
- Posts : 897
Join date : 2014-12-01
Age : 52
Location : Riverdale Georgia
Similar topics
» Another proposed design by Roddie
» Pushrod testing
» Differtent PT-19, P-40, and a Skyraider......
» Cox PT19 info please
» Ski Doo and pt19
» Pushrod testing
» Differtent PT-19, P-40, and a Skyraider......
» Cox PT19 info please
» Ski Doo and pt19
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum