Log in
Search
Latest topics
» WenMac 049 - Glow Plug & Head Gasket replacements?by Ken Cook Today at 8:06 am
» Prop Rod - resto to a runner
by rsv1cox Today at 7:32 am
» A choke-tube with velocity-stack configured Bee
by roddie Today at 6:12 am
» Jim Walkers FireBee - This is going to be fun
by cstatman Yesterday at 6:58 pm
» Hawk had breakfast and then took a bath
by rdw777 Yesterday at 5:38 pm
» Jim Walker Firebaby
by rdw777 Yesterday at 4:58 pm
» Nostalgia alert, my 1959 Corvette revisited
by rsv1cox Yesterday at 2:25 pm
» Prayers for my Wife Please
by akjgardner Yesterday at 10:28 am
» Cox prop rod
by Wiggy Fri May 17, 2024 4:30 pm
» "Red Neck" .049 elec. starter
by getback Fri May 17, 2024 7:19 am
» Cox prop rod
by Wiggy Fri May 17, 2024 5:35 am
» Looking For Comet Tri-Pacer
by latole Fri May 17, 2024 3:45 am
Wrenches Anyone??????
Page 1 of 1
NEW222- Top Poster
- Posts : 3892
Join date : 2011-08-13
Age : 45
Location : oakbank, mb
Re: Wrenches Anyone??????
With such a great quantity, he may want to contact Bernie @Cox International and/or Matt @ExModelEngines . Although wholesale, he might get a better deal overall, plus they could benefit the community by reselling to meet other's needs in return.
GallopingGhostler- Top Poster
-
Posts : 5350
Join date : 2013-07-13
Age : 70
Location : Clovis NM or NFL KC Chiefs
Re: Wrenches Anyone??????
There are two styles of wrenches in there that are useful. The zinc plated one which is thicker and has the wide end that fits the top of the cylinder which utilizes flats. This wrench fully surrounds the plug. The other is the narrower fork which fits the exhaust port and has the two pin spanner hooks. The black Cox wrench is a POS which not only ruins your engine, it can easily injure the user. It slips, it ruins the glow plugs, the screwdriver end which is supposedly for tightening the prop screw is useless. The spanner portion doesn't fit correctly which also destroys anything you use it on.The U shaped portion doesn't fit the flats on the cylinder and if the forked end is used on a cylinder, it will surely ruin it. A clear case of fixing it until it's broke. Obviously, the older wrenches worked and cost more. We certainly couldn't have that.
Ken Cook- Top Poster
- Posts : 5488
Join date : 2012-03-27
Location : pennsylvania
Re: Wrenches Anyone??????
Ken, the earlier wrenches were probably during Leroy Cox's watch, he was a stickler for quality. Too bad he got stuck like other manufacturers in the electric slot car fad that quickly faded, left him with much unsellable useless inventory.
GallopingGhostler- Top Poster
-
Posts : 5350
Join date : 2013-07-13
Age : 70
Location : Clovis NM or NFL KC Chiefs
Re: Wrenches Anyone??????
Interesting tidbits about the wrenches.
NEW222- Top Poster
- Posts : 3892
Join date : 2011-08-13
Age : 45
Location : oakbank, mb
Re: Wrenches Anyone??????
I think I may have one of those shortened wrenches from the late 1970's. Jacob's comment about "too short", could that have been destined for another faceted part of a Cox .049? It already has the cut-out for the cylinder flats, so end portion would not be needed to insert into exhaust ports for removal.
GallopingGhostler- Top Poster
-
Posts : 5350
Join date : 2013-07-13
Age : 70
Location : Clovis NM or NFL KC Chiefs
Re: Wrenches Anyone??????
I have a few of those wrenches that have the exhaust slot end too short. I always thought it was a manufacturing error. They are stamped with a part number of 21530, whereas others are stamped with a part number of 1530.
The one that is too short fits in the exhaust of an early thin wall cylinder, but it doesn't go in enough to overhang. It would apply pressure to wall of the cut, potentially causing a dent in the cylinder wall or slipping and causing a burr. Making me nervous just looking at it.
With a later thick wall cylinder, the later wrench fits it well.
However, this silver wrench doesn't go in enough to overhang to backside of the ports, so it would apply pressure to the wall of the cut, and would be easier to slip with.
The wrench that is "too short" is also too narrow to even fit a thick wall cylinder.
This appeared in the QRC manual from the late 70s:
It's best to not use the exhaust openings at all remove or install a cylinder. A leather strap or blocks of wood in a vice being a better option.
The one that is too short fits in the exhaust of an early thin wall cylinder, but it doesn't go in enough to overhang. It would apply pressure to wall of the cut, potentially causing a dent in the cylinder wall or slipping and causing a burr. Making me nervous just looking at it.
With a later thick wall cylinder, the later wrench fits it well.
However, this silver wrench doesn't go in enough to overhang to backside of the ports, so it would apply pressure to the wall of the cut, and would be easier to slip with.
The wrench that is "too short" is also too narrow to even fit a thick wall cylinder.
This appeared in the QRC manual from the late 70s:
It's best to not use the exhaust openings at all remove or install a cylinder. A leather strap or blocks of wood in a vice being a better option.
Last edited by Admin on Sun Feb 04, 2024 2:30 pm; edited 1 time in total
Re: Wrenches Anyone??????
This is what happens when you use one of those wrenches that are too short:
As posted about here: https://www.coxengineforum.com/t17490-1956-babe-bee-score#226460
As posted about here: https://www.coxengineforum.com/t17490-1956-babe-bee-score#226460
rsv1cox- Top Poster
-
Posts : 10658
Join date : 2014-08-18
Location : West Virginia
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum