Home
Rules
Latest images
Search
Register
Log in
Log in
Search
Latest topics
» Looking For Comet Tri-Pacerby latole Today at 3:45 am
» Cox AT-6 Texan repaint.....Pretty nice
by latole Today at 3:20 am
» Prayers for my Wife Please
by GallopingGhostler Today at 1:59 am
» Cox Ryan ST 2.0
by GallopingGhostler Today at 1:42 am
» "Red Neck" .049 elec. starter
by 944_Jim Yesterday at 7:04 pm
» Jim Walkers FireBee - This is going to be fun
by rdw777 Yesterday at 3:58 pm
» Hawk had breakfast and then took a bath
by rdw777 Yesterday at 3:46 pm
» Roddie's water-cooling bottle for bench-running
by roddie Yesterday at 3:07 pm
» Removing old decals
by latole Yesterday at 3:06 pm
» Prop Rod - resto to a runner
by rsv1cox Yesterday at 2:29 pm
» Blue backplate postage stamp engine
by getback Yesterday at 6:46 am
» COX Postage Stamp engine -Babe Bee & Horseshoe Backplate adapters
by GallopingGhostler Yesterday at 6:33 am
CEF Traveling Engine
Win This Engine!
Live on Patrol
enya 15-III question
Page 1 of 1
enya 15-III question
getback Sun Jan 12, 2014 11:01 am
got this 3303 cl engine at a swap meet last year and it had no needle was gummed up inside , with a good oiling loosened the engine up compression is good. anyway got a 15220 15-19 enya needle valve assy for it installed w/the spray bar hole center hole down ran it yesterday with 8x6 prop all I could get out of it was 9600 rpms , done some checking and I should get 8-16500. my question is this the right needle or and would another get me more hump for my buck ? 
got vedio but have not got my new phone completely set up yet. sorry 
THANKS AS ALWAYS ERIC
got vedio but have not got my new phone completely set up yet. sorry THANKS AS ALWAYS ERIC
getback- Top Poster
Posts : 10159
Join date : 2013-01-18
Age : 66
Location : julian , NC
Re: enya 15-III question
Ken Cook Sun Jan 12, 2014 5:21 pm
The .19 spraybar might have a greater diameter over the .15 size. Drill out the venturi a few thousandth's and retry. That engine runs far greater with a 7x6. The 8x6 would suit the .19 Ken
Ken Cook- Top Poster
- Posts : 5485
Join date : 2012-03-27
Location : pennsylvania
ok there 3 hours later
getback Sun Jan 12, 2014 5:37 pm
[quote="getback"]got this 3303 cl engine at a swap meet last year and it had no needle was gummed up inside , with a good oiling loosened the engine up compression is good. anyway got a 15220 15-19 enya needle valve assy for it installed w/the spray bar hole center hole down ran it yesterday with 8x6 prop all I could get out of it was 9600 rpms , done some checking and I should get 8-16500. my question is this the right needle or and would another get me more hump for my buck ? got vedio but have not got my new phone completely set up yet. sorry THANKS AS ALWAYS ERIC
got vedio but have not got my new phone completely set up yet. sorry THANKS AS ALWAYS ERIC
getback- Top Poster
-
Posts : 10159
Join date : 2013-01-18
Age : 66
Location : julian , NC
Re: enya 15-III question
gcb Sun Jan 12, 2014 5:38 pm
Also check that the piston and cylinder are installed correctly. I got an Enya .15-III for a song because the previous owner had reassembled it incorrectly and apparently couldn't get it to run right.
George
George
gcb- Platinum Member
- Posts : 908
Join date : 2011-08-11
Location : Port Ewen, NY
Similar topics» Question for Enya-philes
» Enya 29-4 Rectangular Venturi question
» Translated Engine instructions for Enya .049-II / Enya .06-II / Enya .08 and Enya .10
» Most expensive Enya in my collection -- Enya 60XLF -GM- SB ring Rear Exhaust
» Enya Engines deal from Ken ---- three .09-II done and a Mikoken/ Enya .049 diesel(special)
» Enya 29-4 Rectangular Venturi question
» Translated Engine instructions for Enya .049-II / Enya .06-II / Enya .08 and Enya .10
» Most expensive Enya in my collection -- Enya 60XLF -GM- SB ring Rear Exhaust
» Enya Engines deal from Ken ---- three .09-II done and a Mikoken/ Enya .049 diesel(special)
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum