Log in
Search
Latest topics
» A choke-tube with velocity-stack configured Beeby roddie Today at 8:23 am
» WenMac 049 - Glow Plug & Head Gasket replacements?
by Ken Cook Today at 8:06 am
» Prop Rod - resto to a runner
by rsv1cox Today at 7:32 am
» Jim Walkers FireBee - This is going to be fun
by cstatman Yesterday at 6:58 pm
» Hawk had breakfast and then took a bath
by rdw777 Yesterday at 5:38 pm
» Jim Walker Firebaby
by rdw777 Yesterday at 4:58 pm
» Nostalgia alert, my 1959 Corvette revisited
by rsv1cox Yesterday at 2:25 pm
» Prayers for my Wife Please
by akjgardner Yesterday at 10:28 am
» Cox prop rod
by Wiggy Fri May 17, 2024 4:30 pm
» "Red Neck" .049 elec. starter
by getback Fri May 17, 2024 7:19 am
» Cox prop rod
by Wiggy Fri May 17, 2024 5:35 am
» Looking For Comet Tri-Pacer
by latole Fri May 17, 2024 3:45 am
Turning down .049 heads for use on a .010
Page 1 of 1
Turning down .049 heads for use on a .010
I don't have a lathe but I was wondering would it be possible to turn .049 heads down to .010 sieve and if so would they fit well enough to run.
Thanks.
Thanks.
Re: Turning down .049 heads for use on a .010
You could probably turn one out and make it fit. I would think it would have lower compression since the element hole is much larger then the element hole in a actual .010 head. Are you running out of spare .010 heads?
Re: Turning down .049 heads for use on a .010
you would have to think about the element body and the ceramic insulator. like said above, the compression would be less then a normal 010 plug.
Carl- Gold Member
- Posts : 141
Join date : 2010-07-31
Age : 66
Location : Montana
Re: Turning down .049 heads for use on a .010
you would also have to consider, that you would have to cut a VERY precise thread, in order to make
a good seal. if the thread thickness (the ridges) doesn't match the inner thread of the cylinder,
there's a chance of pressure loss.i guess it could work, but i'd rather look around for some original heads, to
save myself any frustrating drawbacks, if they don't work. (thus wasting a perfectly good 049 head)
just my opinion.
a good seal. if the thread thickness (the ridges) doesn't match the inner thread of the cylinder,
there's a chance of pressure loss.i guess it could work, but i'd rather look around for some original heads, to
save myself any frustrating drawbacks, if they don't work. (thus wasting a perfectly good 049 head)
just my opinion.
GermanBeez- Platinum Member
- Posts : 1167
Join date : 2011-06-15
Location : Bavaria, Germany
Re: Turning down .049 heads for use on a .010
Ok, I was just wondering I have enough .010 heads and Matt,Bernie and Reggie stock them as well as MECOA and several local and eBay sources.
Thanks.
Thanks.
Similar topics
» The weather is turning in NE MS, USA
» Space Bug Jr. Turning an 8x4
» OEM Cox TD glo-heads NIP now available
» Lathe machining Help needed please?
» How to make reed valves out of a floppy disk
» Space Bug Jr. Turning an 8x4
» OEM Cox TD glo-heads NIP now available
» Lathe machining Help needed please?
» How to make reed valves out of a floppy disk
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum