Log in
Search
Latest topics
» Looking For Comet Tri-Pacerby DanMc Today at 6:25 pm
» "Red Neck" .049 elec. starter
by 944_Jim Today at 6:04 pm
» Cox AT-6 Texan repaint.....Pretty nice
by 944_Jim Today at 3:31 pm
» Prayers for my Wife Please
by balogh Today at 3:08 pm
» Jim Walkers FireBee - This is going to be fun
by rdw777 Today at 2:58 pm
» Hawk had breakfast and then took a bath
by rdw777 Today at 2:46 pm
» Roddie's water-cooling bottle for bench-running
by roddie Today at 2:07 pm
» Removing old decals
by latole Today at 2:06 pm
» Prop Rod - resto to a runner
by rsv1cox Today at 1:29 pm
» Cox Ryan ST 2.0
by 944_Jim Today at 10:52 am
» Blue backplate postage stamp engine
by getback Today at 5:46 am
» COX Postage Stamp engine -Babe Bee & Horseshoe Backplate adapters
by GallopingGhostler Today at 5:33 am
Will a pee wee .020 run decent on a bladder?
Page 1 of 1
Will a pee wee .020 run decent on a bladder?
I am concerned about using the stock fuel tank with a short fuel
pick-up hose to limit run time.
The model is a Sniffer, which may as well be a Pee Wee 30 FF.
Normally they would use a small glass eye-dropper as a fuel
tank. But recently I saw a Sniffer photograph using a bladder.
Unfortunately using the stock tank with the short pick-up hose
creates a problem filling the tank and adjusting the needle because
it is too close to the windshield.
Is a bladder too much fuel pressure for a reed-valved engine?
Thanks
Bill M.
pick-up hose to limit run time.
The model is a Sniffer, which may as well be a Pee Wee 30 FF.
Normally they would use a small glass eye-dropper as a fuel
tank. But recently I saw a Sniffer photograph using a bladder.
Unfortunately using the stock tank with the short pick-up hose
creates a problem filling the tank and adjusting the needle because
it is too close to the windshield.
Is a bladder too much fuel pressure for a reed-valved engine?
Thanks
Bill M.
wmazz- Bronze Member
- Posts : 40
Join date : 2018-12-31
Location : Riverside CA.
Re: Will a pee wee .020 run decent on a bladder?
Bill,
It’s all about the needle. Fine threads work well on pressure and standard threads do not. In your application You may have some trouble.
Some interesting things have been happening lately that would really enhance the .020
Most notably the .020 product backplates that would allow a fine thread needle.
For now your best bet would be a TD .020 with a KK needle.
It’s all about the needle. Fine threads work well on pressure and standard threads do not. In your application You may have some trouble.
Some interesting things have been happening lately that would really enhance the .020
Most notably the .020 product backplates that would allow a fine thread needle.
For now your best bet would be a TD .020 with a KK needle.
Cribbs74- Moderator
-
Posts : 11897
Join date : 2011-10-24
Age : 50
Location : Tuttle, OK
Re: Will a pee wee .020 run decent on a bladder?
A Pee Wee will run fine with a drilled out tank plumbed to an external tank on suction. On the Sniffer you could install a large tank inside nose for long R/C runs and you can also provide an external mount on side of fuselage for an eyedropper for short test flights and/or F/F work.
ticomareado- Account Under Review
- Posts : 1089
Join date : 2013-10-03
Location : NC
Re: Will a pee wee .020 run decent on a bladder?
Try using a balloon if the pressurized fuel supply from a bladder is not a must. I fly R/C and all my COX engines in the 010...09 size range are fed from balloons (simple party balloons sold in toyshops). Resistant to nitro fuel. Light.No need for vent pipe and heavy clunk inside the tank, no foaming, no bubbles in the feedline. Cheap and reliable.
balogh- Top Poster
-
Posts : 4755
Join date : 2011-11-06
Age : 65
Location : Budapest Hungary
Re: Will a pee wee .020 run decent on a bladder?
Any idea on how long a eye-dropper will run for?
Was there a special .020 needle, or was it just a modified KK .049 128tpi needle?
Can a Pee Wee back-plate be modified to fit a 128tpi needle?
Thanks
Bill M.
Cribbs74 wrote:
For now your best bet would be a TD .020 with a KK needle.
Was there a special .020 needle, or was it just a modified KK .049 128tpi needle?
Can a Pee Wee back-plate be modified to fit a 128tpi needle?
Thanks
Bill M.
wmazz- Bronze Member
- Posts : 40
Join date : 2018-12-31
Location : Riverside CA.
Re: Will a pee wee .020 run decent on a bladder?
An eye dropperful with about 4 to 5 inches of fuel line ought to go from 35 to 50 seconds on a Pee Wee. I have a Dakota FF with a cox .049 single port horseshow that will run about 25 to 30 seconds on 12 ml eyedropperful with out 4 inches of fuel line. I never launch it full however.
ticomareado- Account Under Review
- Posts : 1089
Join date : 2013-10-03
Location : NC
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum