Log in
Search
Latest topics
» Hawk had breakfast and then took a bathby rsv1cox Today at 10:26 am
» Jim Walkers FireBee - This is going to be fun
by getback Today at 9:55 am
» A choke-tube with velocity-stack configured Bee
by roddie Today at 8:23 am
» WenMac 049 - Glow Plug & Head Gasket replacements?
by Ken Cook Today at 8:06 am
» Prop Rod - resto to a runner
by rsv1cox Today at 7:32 am
» Jim Walker Firebaby
by rdw777 Yesterday at 4:58 pm
» Nostalgia alert, my 1959 Corvette revisited
by rsv1cox Yesterday at 2:25 pm
» Prayers for my Wife Please
by akjgardner Yesterday at 10:28 am
» Cox prop rod
by Wiggy Fri May 17, 2024 4:30 pm
» "Red Neck" .049 elec. starter
by getback Fri May 17, 2024 7:19 am
» Cox prop rod
by Wiggy Fri May 17, 2024 5:35 am
» Looking For Comet Tri-Pacer
by latole Fri May 17, 2024 3:45 am
Would Like to Adapt a Carb on a Cox TeeDee .15
Page 1 of 1
Would Like to Adapt a Carb on a Cox TeeDee .15
I was wondering if anyone had tried adapting an aftermarket Carb to a Cox Tee Dee .15? If So, What Aftermarket did you use and was there any success, Pros / Cons?
Respectfully, Jim "P" Jenuine-Motor-Cox
Respectfully, Jim "P" Jenuine-Motor-Cox
Jenuine Motor- Moderate Poster
- Posts : 12
Join date : 2017-08-19
Age : 73
Location : Portland Oregon 97217
Re: Would Like to Adapt a Carb on a Cox TeeDee .15
I have works great
Norvel RC Carb used:
Thread is .375 x 32 aka (3/8 - 32) die I do not have a way to turn the neck down so flipped
the carb upside down and threaded the venturi side the hour glass cut inside the throat is on both ends.
I have not cut down the venturi intakes but may the upswing is good idle left as is.
Norvel RC Carb used:
Thread is .375 x 32 aka (3/8 - 32) die I do not have a way to turn the neck down so flipped
the carb upside down and threaded the venturi side the hour glass cut inside the throat is on both ends.
I have not cut down the venturi intakes but may the upswing is good idle left as is.
1/2A Nut- Top Poster
- Posts : 3442
Join date : 2013-10-20
Age : 60
Location : Brad in Texas
Re: Would Like to Adapt a Carb on a Cox TeeDee .15
1/2A Nut wrote:I have works great
Norvel RC Carb used:
Thread is .375 x 32 aka (3/8 - 32) die I do not have a way to turn the neck down so flipped
the carb upside down and threaded the venturi side the hour glass cut inside the throat is on both ends.
I have not cut down the venturi intakes but may the upswing is good idle left as is.
Nice clean conversion 1/2 A Nut. I like the angled needle valve too.
Basswood
Basswood- Gold Member
- Posts : 141
Join date : 2020-02-19
Age : 67
Location : Phoenix, Az.
Similar topics
» Putting a Medallion carb Body on a TeeDee 051
» WTB: TeeDee Aluminum Carb Body
» TeeDee 051 carb sleeve replacement
» COX 010 TeeDee with RC carb, courtesy sosam 117
» Putting a Medallion carb Body on a TeeDee 051
» WTB: TeeDee Aluminum Carb Body
» TeeDee 051 carb sleeve replacement
» COX 010 TeeDee with RC carb, courtesy sosam 117
» Putting a Medallion carb Body on a TeeDee 051
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum